Crow Runner Link Manuel d'utilisateur

ELECTRONIC ENGINEERING LTD. Runner Link Gateway ADD-ON INTERNET ALARM COMMUNICATION BOARD (TCP/IP) Installation and Programming Guide P/N 7111751

RUNNER LINK Gateway Installing the Unit 7 Table 1 LED Description Table LED Description Fail Solid Red when pressing the Config button or when t

8 Configuring the Runner Link In order to configure the Runner Link you must first communicate with it using the initial setup IP of 192.168.0.5 and

RUNNER LINK Gateway Configuring the Runner Link 9 4. Right-click the active Local Area Connection icon 5. Click Properties. 6. Double-click I

RUNNER LINK Gateway Configuring the Runner Link 10 7. Select Use the following IP address radio button. 8. Enter an IP address of 192.168.0.5. 9.

RUNNER LINK Gateway Configuring the Runner Link 11 3. On the Runner Link board, press the Config button for minimum of 3 seconds. The red FAIL LE

RUNNER LINK Gateway Configuring the Runner Link 12 Setting the Board to the Factory Default IP Address 1. Using Figure 3 on page 6 as a guide, sho

13 Upload/Download Program (Virtual Keypad) The program enables the Monitoring Service Provider to control your Alarm System in real time over the I

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 14 2. Click the Communication menu. 3. Click Request. There are two ways to com

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 15 Initiating Communication with the Unit Using the Unit IP Address 1. In the Direct

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 16 Using the Account Number and Receiver Server IP Address 1. In the Search for Recei

Crow Limited Warranty (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period o

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 17 Example 1 - Taking Control of the Unit (Alarm/Disarm) NOTE Using this program yo

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 18 For information on how to configure the unit, see the Upload/Download manual vi

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 19 Example 2 - Changing the Password (Installer Mode) This section explains how to ch

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 20 4. Click Users. 5. In the Code field (password), enter a new password. 6. Cli

RUNNER LINK Gateway Upload/Download Program (Virtual Keypad) 21 Example 3 - Changing the Phone Number This section explains how to change the phon

22 Installing the Receiver Server Configuration Program NOTES The Receiver servers are installed on the premises of the Monitor Service Provider.

RUNNER LINK Gateway Installing the Receiver Server Configuration Program 23 3. Select the "I accept" the terms of the license agreement

RUNNER LINK Gateway Installing the Receiver Server Configuration Program 24 8. Click the button. 9. Click the to install the program.

RUNNER LINK Gateway Installing the Receiver Server Configuration Program 25 10. Click the button to exit the wizard. 11. Click the button to

RUNNER LINK Gateway Installing the Receiver Server Configuration Program 26 15. Click the button. 16. Click the button to start the service.

i Contents INTRODUCTION...1 S

1 Introduction The RUNNER LINK Gateway is a small external hardware addition to Crow’s Runner Control Panel Series. It is connected to the Alarm Sys

RUNNER LINK Gateway Introduction 2 Benefits  Connecting intruder alarm equipment to the Internet  Supporting standard alarm protocols (SIA/CID

RUNNER LINK Gateway Introduction 3 Monitoring Service Provider The Monitoring Service Provider is located in a tamper proof environment and uses m

RUNNER LINK Gateway Introduction 4 Shipping Contents Hardware  RUNNER LINK Gateway module  RJ-45 Ethernet cross Cable  Fast Bus connection

5 Installing the Unit Installing the Software Installing the Installer Configuration Software Installing the Runner Link™ On your PC This software p

RUNNER LINK Gateway Installing the Unit 6 Connecting Cables 1. Connect one end of the bus cable to the bus on the control panel main board. You